15/16 GAUGE NAILER
MODEL G6048
INSTRUCTION MANUAL
COPYRIGHT © MAY, 2002 BY GRIZZLY INDUSTRIAL, INC.
1821 VALENCIA ST., BELLINGHAM, WA 98227
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
PRINTED IN TAIWAN
ONLINE MANUAL DISCLAIMER
THE INFORMATION IN THIS MANUAL REPRESENTS THE CONFIGURATION OF THE MACHINE AS IT IS CUR-
RENTLY BEING SHIPPED. THE MACHINE CONFIGURATION CAN CHANGE AS PRODUCT IMPROVEMENTS
ARE INCORPORATED. IF YOU OWN AN EARLIER VERSION OF THE MACHINE, THIS MANUAL MAY NOT
EXACTLY DEPICT YOUR MACHINE . CONTACT CUSTOMER SERVICE IF YOU HAVE ANY QUESTIONS ABOUT
DIFFERENCES. PREVIOUS VERSIONS ARE NOT AVAILABLE ONLINE.
Safety Instructions For Pneumatic Tools
18. DISCONNECT TOOLS before ser-
10. USE PROPER AIR HOSE for the
tool. Make sure your air hose is in
good condition and is long enough to
reach your work without stretching.
vicing and changing accessories.
19. USE
THE
RECOMMENDED
Consult the
ACCESSORIES.
owner’s manual for recommended
accessories. The use of improper
accessories may cause risk of
injury.
11. WEAR PROPER APPAREL. Do not
wear loose clothing, gloves, neck-
ties, rings, bracelets, or other jewel-
ry which may get caught in moving
parts. Non-slip footwear is recom-
mended. Wear a protective hair cov-
ering to contain long hair.
20. CHECK
DAMAGED
PARTS.
Before further use of the tool, a
guard or other part that is damaged
should be carefully checked to
determine that it will operate prop-
erly and perform its intended func-
tion. Check for alignment of moving
parts, binding of moving parts,
breakage of parts, mounting, and
any other conditions that may affect
its operation. A guard or other part
that is damaged should be properly
repaired or replaced.
12. ALWAYS USE SAFETY GLASSES.
Also use a face or dust mask if cut-
ting operation is dusty. Everyday
eyeglasses only have impact resis-
tant lenses, they are NOT safety
glasses.
13. WEAR APPROVED HEARING
PROTECTION.
14. SECURE WORK. Use clamps or a
vise to hold work when practical. It is
safer than using your hand and frees
both hands to operate tool.
21. NEVER LEAVE UNATTENDED
TOOL CONNECTED TO AIR.
Disconnect the air hose and do not
leave tool until it is relieved of any
built up pressure.
15. DO NOT OVERREACH. Keep prop-
er footing and balance at all times.
16. MAINTAIN TOOLS WITH CARE.
Keep tools lubricated and clean for
best and safest performance. Follow
instructions for lubricating and
changing accessories.
22. NEVER ALLOW UNTRAINED
USERS TO USE THIS TOOL
WHILE UNSUPERVISED.
23. IF YOU ARE UNSURE OF THE
INTENDED OPERATION, STOP
USING THE TOOL. Seek formal
training or research books or maga-
zines that specialize in pneumatic
tools.
17. REDUCE THE RISK OF UNINTEN-
TIONAL STARTING. Do not carry
tool with hand on trigger and always
disconnect from air when not in use.
-2-
G6048 15/16 Gauge Nailer
Basic Nailer Safety
In addition to the rules stated in the previ-
ous section, and those in the warning
boxes throughout this manual, please
observe the following safety tips for your
new nailer:
1. READ THIS ENTIRE MANUAL
BEFORE OPERATING THE NAIL-
ER.
2. ALWAYS DISCONNECT AIR FROM
THE NAILER whenever servicing or
installing nails. During maintenance,
a nailer connected to air may fire acci-
dentally, causing serious personal
injury.
3. DO NOT PLACE HANDS NEAR
NAIL POINT OF ENTRY. Nail can
deflect and be driven through the sur-
face of the workpiece, puncturing
your hand or fingers.
Operating this nailer can propel
objects into the air, causing immedi-
ate eye damage. To protect yourself,
always wear American National
Standards Institute (ANSI) approved
safety glasses or goggles when oper-
ating this equipment. In addition, this
nailer discharges at 85-90 decibels.
To protect your hearing, always wear
ANSI approved ear protection when
operating this nailer.
4. NEVER CONNECT THE NAILER TO
PRESSURIZED
OXYGEN
OR
OTHER COMBUSTIBLE GASES as
a power source. Only use filtered,
lubricated, and regulated compressed
air.
5. ALWAYS
KEEP
ANY
BYSTANDERS BEHIND NAILER
OR AWAY FROM AREA DURING
USE. Nails may be driven completely
though wood and could become dan-
gerous projectiles.
6. DO NOT CARRY THE NAILER BY
ANY OTHER PART THAN THE
HANDLE, and do not carry the nailer
by the air hose.
7. DO NOT KEEP THE TRIGGER
PULLED ON THE SAFETY YOKE
MECHANISM WHEN CARRYING
OR HOLDING THE TOOL.
Never point this nailer at yourself or
another person! Always pay attention
to the direction this nailer is pointed.
Use this tool with respect and caution
to lessen the possibility of operator or
bystander injury. Ignoring this warn-
ing may result in serious personal
injury.
8. DO NOT USE A CHECK VALVE OR
ANY OTHER FITTING that allows air
to remain in the tool.
G6048 15/16 Gauge Nailer
-3-
INTRODUCTION
Most importantly, we stand behind our
Commentary
tools. If you have any service questions or
parts requests, please call or write us at
the location listed below.
We are proud to offer the Grizzly Model
G6048 15/16 Gauge Nailer. This model is
part of a growing Grizzly family of fine
power tools. When used according to the
guidelines set forth in this manual, you can
expect years of trouble-free, enjoyable
operation and proof of Grizzly’s commit-
ment to customer satisfaction.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail: [email protected]
This Model G6048 features 360˚
adjustable exhaust, a quick release nose
clamp, a convenient side-loading maga-
zine, a safety trigger and a durable plastic
carrying case. The Model G6048 shoots
3
15/16 gauge brad nails ⁄4"-21⁄2" in length
and accepts up to 100 nails at a time. At
4.8 lbs., this model is also easy to carry
around for hours.
We are pleased to provide this manual
with the Model G6048. It was written to
encourage safety considerations and
guide you through general operating pro-
cedures and maintenance. This manual
represents our effort to produce the best
documentation possible.
Read the manual before assembly
and operation. Become familiar with
this tool, its safety instructions, and
its operation before beginning any
work. Serious personal injury may
result if safety or operational infor-
mation is not understood or followed.
The specifications, details, and pho-
tographs in this manual represent the
Model G6048 as supplied when the man-
ual was prepared. However, owing to
Grizzly’s policy of continuous improve-
ment, changes may be made at any time
with no obligation on the part of Grizzly. If
you have any comments regarding this
manual, please write to us at the address
below:
Grizzly Industrial, Inc.
Technical Documentation
P.O. Box 2069
C
/O
Bellingham, WA 98227-2069
-4-
G6048 15/16 Gauge Nailer
Compressed Air System
Safety Yoke Mechanism
The Model G6048 is designed to be oper-
ated at 75-110 psi. Do not exceed the
maximum operating pressure!
A safety yoke mechanism (bump fire) on
the nose of the nailer acts as a secondary
safety device. When the trigger is pressed,
the nailer will not fire until the safety yoke
mechanism is depressed.
Before you use your new nailer, regulate
the air pressure on your air compressor to
barely over the minimum psi for your nail-
er. Increase air pressure only if needed.
Before you use your nailer for the first time,
check the safety yoke mechanism to
ensure proper function. To do this:
Many pneumatic tools benefit from an in-
line filter/lubricator/regulator unit. This
attachment is connected by hoses
between the air compressor and the nailer.
Using this unit protects your tool from dam-
aging water build-up, allows you to adjust
and maintain constant air pressure to your
tool, and saves you the inconvenience of
having to manually lubricate your tool
every time you use it. Check the current
Grizzly catalog for availability of this unit. If
you plan on installing a filter/lubricator/reg-
ulator unit in your compressed air system,
always follow the connection instructions
that come with the unit.
1. Make sure the nailer is disconnect-
ed from the air supply!
2. Make sure the magazine is empty and
contains no nails.
3. Make sure the trigger and the safety
yoke mechanism move up and down
without sticking.
4. Connect the nailer to the air supply.
5. Without pressing the trigger,
depress the safety yoke mechanism
against a scrap piece of wood that is
clean and free of any knots, nails, or
other foreign objects. If the nailer
does not fire, then the safety yoke
mechanism is working correctly. If the
nailer does fire when you do this,
immediately disconnect the nailer
from the air supply and call our cus-
tomer service for help.
Similarly if the nailer fires when the trigger
is pulled, without the safety yoke mech-
anism being depressed, then the nailer is
not working properly.
If either of these two conditions develop
after you have used your nailer for a peri-
od of time, check the lubrication of these
mechanisms.
Exceeding the maximum permissible
operating pressure may cause the
nailer to explode, blowing metal frag-
ments in all directions. To protect
yourself from serious personal injury,
DO NOT allow your air compressor to
exceed the recommended pressure
when connected to this nailer!
The safety yoke is a mechanical
device that can fail. Never rely on the
safety yoke mechanism as an excuse
to point the nailer at yourself or any
bystanders. Serious injury may occur.
-5-
G6048 15/16 Gauge Nailer
OPERATION
When replacing nails for your Model
G6048, follow these guidelines:
Loading Nailer
To load your nailer:
Gauge: 15/16
Length:
Capacity: 100 Nails
3
⁄ "
4"-21⁄2
1. Disconnect the air supply from the
nailer!
2. Flip the magazine latch in the direc-
tion shown in Figure 1.
Single/Bump Fire Mode
The Model G6048 is equipped with a sin-
gle/bump fire trigger.
To select single or bump fire operation:
1. Disconnect the air supply from the
nailer!
2. Locate the hex nut that secures the
safety yoke mechanism to the trigger
housing. See Figure 3.
Figure 1. Releasing magazine latch.
3. To select Single Fire mode, tighten
the hex nut completely.
4. To select Bump Fire mode, unthread
the hex nut at least two full turns.
3. Pull back the magazine cover until it
stops.
4. Point the nailer down and insert a
stick of nails into the magazine as
shown in Figure 2. Make sure the
pointed ends of the nails rest in the
slot at the bottom of the magazine.
Adjustment
Hex Nut
Figure 3. Single/bump fire adjustment.
Figure 2. Loading brad nails into nailer.
5. Push the magazine cover forward
until the magazine latch locks in
place.
-6-
G6048 15/16 Gauge Nailer
Besides damaging your workpiece,
deflection can cause injury if your free
hand is securing the workpiece in the
location that the nail deflects.
Operating Nailer
If you have not read the safety instruc-
tions in this manual, do not operate the
nailer.
4. Press the trigger. If the nail drove into
the wood far enough, continue with
your intended operations. If the nail
either went too far or not far enough,
then adjust the air pressure. More air
pressure will make the nail go deeper
and less air pressure will decrease
the nail penetration.
Periodically, place one drop of the included
oil into the quick connect fitting where the
nailer connects to the air supply. After oil-
ing, wipe off any excess oil near the nailer
exhaust to avoid dust build-up.
To operate your nailer:
1. Connect the air supply to the quick
connect fitting.
2. Test the loaded nailer for proper pen-
etration. Hold the nailer perpendicular
to the surface of a piece of clean
scrap wood that is thick enough for
the length of nails you have loaded.
Depress the safety yoke mechanism
on your workpiece.
3. Before pressing the trigger, make
sure your free hand is positioned out
of the way of a potential path of a nail
in case of deflection. (Deflection is
caused when the nail changes its
path, resulting in the nail puncturing
the surface of the workpiece as
shown in Figure 4.)
Figure 4. Example of nail deflection.
-7-
G6048 15/16 Gauge Nailer
To clear a jammed nail from the discharge
area with the Model G6048:
Clearing Jammed Nails
The most frequent situation with any type
of nailer is a nail jam. A jammed nail must
be cleared before using the nailer again.
The two places where a nail can get
jammed are the magazine and the dis-
charge area.
1. Disconnect the nailer from the air
supply!
2. Remove all of the brad nails from the
magazine.
3. Flip up the quick release latch that is
located on top of the nailer nose
assembly as shown in Figure 5.
4. Remove the driver guide cover.
5. The jammed nail should now be visi-
ble; remove it from the discharge area
with needle nose pliers.
6. Replace the driver guide cover and
snap the quick release latch back into
operating position.
Quick Release Latch
Always disconnect air from nailer
whenever clearing a jammed nail!
Driver Guide Cover
To clear a jammed nail from the magazine:
1. Disconnect the nailer from the air
supply!
2. Open the magazine cover and pull the
magazine all the way back.
Figure 5. Removing guide cover.
3. Locate and remove the jammed brad
nail with a pair of needle nose pliers.
Close the magazine cover so it latch-
es.
-8-
G6048 15/16 Gauge Nailer
Oiling Nailer
Cleaning Nailer
Special oil has been included with you new
Grizzly Nailer. Periodically place one drop
of oil in the nailer air inlet (as shown in
Figure 6). After oiling, wipe off any excess
oil near the nailer exhaust to avoid dust
build-up. When the oil that was included
with the nailer has been completely used,
replace with Grizzly Model G2820
Pneumatic Tool Oil.
Use a good solvent to clean the nailer
nose assembly. Always be sure that the
nailer is dry before using it again.
Do not allow dust, chips, sand, etc. into the
air connectors or into the body of the nail-
er; this may result in leaks and damage to
the nailer and the air fittings.
Another option to manual oiling would be
to install a lubricator in your air compressor
line. If your air compressor line already has
a lubricator, then regular lubrication of your
nailer will not be necessary. Just make
sure there is always oil in the lubricator.
As mentioned before, the best option is to
install a filter/lubricator/regulator unit such
as the Grizzly Model H2333 in your air line.
Never use gasoline or other flamma-
ble liquids to clean this tool. Vapors
in the tool may ignite, causing the
tool to explode. Ignoring this warning
may lead to serious personal injury or
even death!
Figure 6. Lubricating nailer via air inlet.
NOTICE
Too much oil in the nailer will ruin
the O-rings!
Always disconnect air from nailer
whenever servicing! During mainte-
nance, a nailer connected to air may
fire accidentally, causing serious
personal injury!
-9-
G6048 15/16 Gauge Nailer
Replacing Pistons/O-Rings
If you use your nailer day in and day out,
Grizzly offers repair pistons as cheap
insurance against wasted down time and
lost profits in the event that a piston or pis-
ton shaft becomes worn out. To replace a
piston:
Figure 7. Removing nailer exhaust cap.
8. With a long flathead screwdriver or
similarly shaped tool, push the piston
shaft back inside the nailer until you
can grip the piston head and remove
it from the cylinder. (Be careful not to
scratch the discharge area when
pushing the piston shaft with the
screwdriver.)
9. Place a new O-ring on the new piston
and apply a thin film of the nailer lubri-
cating oil on the O-ring.
Always disconnect air from nailer
whenever servicing! During mainte-
nance, a nailer connected to air may
fire accidentally, causing serious
personal injury!
10. Insert the new piston in the cylinder.
Make sure that the grooves on the
piston shaft line up with those on the
guide at the bottom of the cylinder.
The new piston should easily slide
into the cylinder. Do not force the
piston into the cylinder! If the piston
is not easily inserted, double-check
the alignment of the piston shaft with
the grooves on the guide.
1. Disconnect the nailer from the air
supply!
2. Remove all nails from the magazine
cartridge.
3. Remove the 4 cap screws from the
nailer exhaust cap.
4. Remove the exhaust cap as shown in
Figure 7.
11. After the piston is inserted correctly,
close the magazine. Replace the rear
cap assembly and tighten the 4 cap
screws.
5. The top of the piston should now be
visible inside the cylinder, which is
housed in the head of the nailer.
6. Open the magazine.
12. For more assistance, or to install a
complete O-ring set, refer to the
appropriate breakdown diagram in the
back of this manual.
7. Watch the discharge area and push
the top of the piston with your finger.
You will see the piston shaft slide
down the discharge area.
-10-
G6048 15/16 Gauge Nailer
G6048 PART BREAKDOWN
-11-
G6048 15/16 Gauge Nailer
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
01 P6048001 LOCK NUT
02 P6048002 EXHAUST COVER
03 P6048003 SPRING PLATE
05A P6048005A CAP SCREW + SW
06 P6048006 CAP
39 P6048039 O-RING
40 P6048040 O-RING
41 P6048041 VALVE PLUNGER
42 P6048042 PLUNGER
43 P6048043 O-RING
07A P6048007A BUTTON HD CAP SCR
08 P6048008 SPACER
44 P6048044 PLUNGER CAP
45B P6048045B TRIGGER ASSEMBLY
47 P6048047 ROLLED PIN
48A P6048048A LATCH
09 P6048009 PISTON STOPPER
10 P6048010 SPRING
11 P6048011 O-RING
49 P6048049 BALL PIN
12 P6048012 PISTON HEAD VALVE
13 P6048013 O-RING
50 P6048050 GUIDE COVER
51A P6048051A NOSE
14 P6048014 SEAL
52 P6048052 MAGAZINE COVER
53A P6048053A SETSCREW
54 P6048054 MAGAZINE
55A P6048055A BUTTON HD CAP SCR
56 P6048056 TAIL COVER
57 P6048057 PUSHER
15A P6048015A O-RING
16A P6048016A PISTON ASSEMBLY
18 P6048018 CYLINDER SPACER
19 P6048019 O-RING
20 P6048020 O-RING
21A P6048021A CYLINDER
21-1 P6048021-1 O-RING
58 P6048058 SLIDE BLOCK
59A P6048059A SPRING
22 P6048022 BUMPER
24 P6048024 GASKET
60 P6048060 NAIL GUIDE LINER
61A P6048061A JOINT GUIDE
62 P6048078 CAP SCREW
66A P6048066A BRACKET ASSEMBLY
68A P6048068A CAP SCREW
69 P6048069 LOCK NUT
70A P6048070A GASKET
25 P6048025 BODY
26 P6048026 E RING
27 P6048027 GASKET
28 P6048028 STEPPED PIN
29A P6048029A BOTTOM
29-1 P6048029-1 O-RING
71 P6048071 REAR COVER
72 P6048072 AIR PLUG
73A P6048073A CAP SCREW
73-1 P6048073-1 FLAT WASHER
74A P6044075A CAP SCREW
80A P6048080A CAP SCREW
81 P6048081 O-RING
30A P6044005A CAP SCREW
31 P6048031 SPRING GUIDE
32A P6048032A SAFETY LEVER
33 P6048033 SPRING
34 P6048034 SAFETY LEVER
36 P6048036 O-RING
37 P6048037 VALVE
82 P6048082 O-RING
38 P6048038 O-RING
83 P6048083 SPRING
-12-
G6048 15/16 Gauge Nailer
TROUBLESHOOTING
CAUSE
PROBLEM
ACTION
1. O-rings in trigger valve
housing are damaged.
1. O-rings must be replaced
& operation of safety
yoke must be checked.
Air leaking at trigger valve
area.
1. Loose screws in housing.
2. Damaged O-ring.
3. Loose air fitting.
1. Tighten screws.
2. Replace O-ring.
3. Tighten air fitting.
Air leaking between hous-
ing and hose.
1. Damaged seal.
1. Air leaks.
1. Replace damaged seals.
Air leaking between hous-
ing and cap assembly.
1. Tighten screws and fit-
tings.
Tool skips nails while dis-
charging.
2. Dirt in nose.
2. Clean nose.
3. Dirt or damage prevents
nails from moving freely in
magazine.
3. Clean magazine and
inspect/repair damage.
4. Inadequate air flow to tool.
4. Check fitting, hose, com-
pressor & air pressure.
5. Replace piston O-ring.
Lubricate.
5. Worn O-ring on piston or
lack of lubrication.
6. Damaged O-rings on trigger
valve.
6. Replace trigger valve O-
rings.
7. Worn bumper.
8. Cap seal leaking.
7. Replace bumper.
8. Replace cap seal.
1. Nailer is not sufficiently lubri-
1. Lubricate nailer.
2. Replace spring.
Tool runs slowly or has a
loss of power.
cated.
2. Broken spring in cap assem-
bly.
3. Exhaust port in cap is
blocked.
3. Clean or replace dam-
aged internal parts.
1. Nails are the wrong size.
2. Nails are bent.
3. Magazine or nose screws
are loose.
1. Use correct nails.
2. Use undamaged nails.
3. Tighten magazine and
nose screws.
Fasteners frequently jam
the nailer.
4. Driver or driver guide are
worn or damaged.
4. Replace worn or dam-
aged parts.
1. Nail is jammed in maga-
zine or discharge area.
1. Clear nailer magazine or
discharge area.
Nailer does not fire.
2. Piston shaft is damaged.
3. Air pressure too low.
2. Replace piston shaft.
3. Check/increase air pres-
sure.
G6048 15/16 Gauge Nailer
-13-
WARRANTY AND RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original
purchaser from the date of purchase. This warranty does not apply to defects due directly
or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main-
tenance. This is Grizzly’s sole written warranty and any and all warranties that may be
implied by law, including any merchantability or fitness, for any particular purpose, are here-
by limited to the duration of this written warranty. We do not warrant or represent that the
merchandise complies with the provisions of any law or acts unless the manufacturer so
warrants. In no event shall Grizzly’s liability under this warranty exceed the purchase price
paid for the product and any legal actions brought against Grizzly shall be tried in the State
of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, con-
tingent, special, or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details.
We will then issue you a “Return Authorization Number,” which must be clearly posted on
the outside as well as the inside of the carton. We will not accept any item back without this
number. Proof of purchase must accompany the merchandise.
The manufacturers reserve the right to change specifications at any time because they con-
stantly strive to achieve better quality equipment. We make every effort to ensure that our
products meet high quality and durability standards and we hope you never need to use this
warranty.
Please feel free to write or call us if you have any questions about the machine or the man-
ual.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail:
Thank you again for your business and continued support. We hope to serve you again
soon!
-14-
G6048 15/16 Gauge Nailer
WARRANTY CARD
Name__________________________________________________________
Street__________________________________________________________
City____________________State________Zip_________
Phone Number____________E-Mail___________________FAX____________
Model #_______________Serial#________________Order #______________
The following information is given on a voluntary basis. It will be used for marketing purposes to help
us develop better products and services. Of course, all information is strictly confidential.
9. How many of the machines checked above are
Grizzly? ____________
1. How did you learn about us?
___Advertisement
___Friend
___Catalog
___World Wide Web
___Other__________________________
___Card Deck
10. Which portable/hand held power tools do you own?
Check all that apply.
___Belt Sander
___Biscuit Joiner
___Circular Saw
___Detail Sander
___Drill/Driver
___Orbital Sander
___Palm Sander
___Portable Planer
___Saber Saw
___Reciprocating Saw
___Router
2. What is your annual household income?
___$20,000-$29,999
___$30,000-$39,999
___$40,000-$49,999
___$50,000-$59,999
___$60,000-$69,999
___$70,000-$79,999
___$80,000-$89,999
___$90,000 +
___Miter Saw
___Other_________________________________
3. What is your age group?
___20-29
11. What machines/supplies would you like Grizzly
Industrial to carry?
___50-59
___60-69
___70 +
___30-39
___40-49
________________________________________
________________________________________
________________________________________
________________________________________
4. How long have you been a woodworker?
___0 - 2 Years
___2 - 8 Years
___8 - 20 Years
___20+ Years
12. What new accessories would you like Grizzly
Industrial to carry?
5. How would you rank your woodworking skills?
________________________________________
________________________________________
________________________________________
________________________________________
___Simple
___Advanced
___Intermediate
___Master Craftsman
6. What stationary woodworking tools do you own?
Check all that apply.
13. What other companies do you purchase your tools
and supplies from?
___Air Compressor
___Band Saw
___Panel Saw
___Planer
_________________________________________
_________________________________________
_________________________________________
___Drill Press
___Power Feeder
___Radial Arm Saw
___Shaper
___Jointer
___Lathe
___Drum Sander
___Dust Collector
___Spindle Sander
___Table Saw
14. Do you think your purchase represents good value?
___Yes
___No
___Mortiser
___Wide Belt Sander
___Horiz.Boring Machine
___Vacuum Veneer Press
___Other______________________________
15. Would you recommend Grizzly to a friend?
___Yes ___No
16. Would you allow us to use your name as a refer-
ence for Grizzly customers in your area? Note: We
never use names more than three times.
7. How many of your woodworking machines are
Grizzly? _____________
___Yes
___No
8. Which benchtop tools do you own? Check all
that apply.
17.Comments:________________________________
_________________________________________
_________________________________________
_________________________________________
___1"x42" Belt Sander ___6" - 8" Grinder
___5" - 8" Drill Press ___Mini Lathe
___8" Table Saw
___Scroll Saw
___8" - 10" Bandsaw
___Disc/Belt Sander
___Spindle/Belt Sander ___Mini Jointer
___10"-12"Thickness Planer
___Other______________________________
Send a Grizzly Catalog to a friend:
Name________________________________
Street________________________________
City______________State______Zip_______
FOLD ALONG DOTTED LINE
Place
Stamp
Here
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
TAPE ALONG EDGES--PLEASE DO NOT NAIL
|