USER MANUAL
HLT71
7'' DIGITAL LCD TV
IMPORTANT
READ THESE INSTRUCTIONS
BEFORE USE AND RETAIN
FOR FUTURE REFERENCE.
WARNINGS:
— This TV monitor should be operated only at the adaptor
Controls
supplied.
— Do not try to repair the TV monitor yourself as it contains
no user-serviceable parts. The TV monitor should only be
repaired by a qualified technician.
— Stop using the TV monitor if the cabinet is damaged.
Have it checked by a service technician.
— Put your monitor only in a clean, dry environment. Unplug
the monitor immediately if it gets wet, and consult your
service technician.
— Always unplug the monitor before cleaning it. Clean the
cabinet with a clean, dry cloth. Apply non-ammonia-based
cleaner onto the cloth, not directly onto the glass screen.
— Keep the TV monitor away from magnetic objects, motors,
TV sets, and transformers.
— Do not place heavy objects on the cable or power cord.
Care and Maintenance
3 4 5 6 7 8 9 10 11 12 13
— Avoid exposing your monitor directly to sunlight or other
heat sources. Place your TV monitor away from the sun
to reduce glare.
14
— Put your TV monitor in a well-ventilated area. Do not
place anything heavy on top of your monitor.
— Make certain that your TV monitor is installed in a clean
and moisture-free area.
15
16
17
18
Safety Tips
1
2
— If smoke, abnormal noise or odor comes out of your TV
monitor, switch off the power immediately and call your
service center.
— Never try to repair the TV monitor yourself. Always call
your service center or a qualified technician to fix it.
— Do not watch during driving, it is dangerous and is illegal!
Note
This user's manual contains graphics and information that is
for reference purposes only and is subject to change without
notice.
20
Power requirements
You may use the DC adaptor or the Cigarette lighter adaptor
(NEGATIVE GROUND ONLY) supplied for the power source.
Battery installation
Attach the rechargeable battery pack to the bottom of the
TV Player unit as illustrated below:
19
1. Power on/off switch
2. DC input jack
3. LCD display
4. Speaker
5. Standby/Power indicator
6. Menu
7. Channel -
8. Channel +
9. Auto/OK
10. Volume - (
11. Volume + (
12. Mode
right key in menu function)
left key in menu function)
13. Remote control sensor
14. RF in
15. Video in jack
BATTERY
BATTERY COVER
16. Audio left in jack
17. Audio right in jack
18. Phones jack
19. Self-support Bracket
20. Battery compartment
NOTE:
This unit works either on the battery pack supplied or on DC
power: unplug the DC Power adapter from the DC input jack
to run off the battery pack (after fully charged); plugging the
DC Power adapter while the battery pack is attached
initiates the charging of this battery. Please insert the battery
correctly. Generally, it takes about 6 hours to charge a dead
battery pack full. A full charged battery pack can endure
approximately 2 hours of continuous playback.
2
Remote control operation
HOW TO USE ANTENNA
Directly connect external movable antenna to RF in, may
also connect roof antenna directly.
POWER
MUTE
For better reception:
1
10
11
ZOOM
EPG
PICTURE
MENU
MTS
Adjust the direction/position of the antenna. The signal
strength depends on the area of reception. If the signal is
too weak, poor or no reception is possible. This is not a
malfunction.
2
3
4
5
SLEEP
EXIT
12
13
ATTENTION:
Do not rotate the antenna in counter direction after fixing, it
may get loose & effect the channel reception.
ENTER
6
14
15
16
TV/AV
INFO
CH+
1
4
7
2
5
8
3
6
9
7
17
CH-
18
19
20
0
8
9
+
VOLUME
Note:
a) Point the remote control unit from no more than about
5m from the remote control sensor and within about
60° of the front of the TV monitor.
b) Do not press the button too quick. Press the button
after the previous operation is completed.
1. MUTE: Used to toggle between normal & muted audio.
2. PICTURE: Press this button to select the picture display
effect between Dynamic, soft, personal or standard.
3. MTS: Press to select the audio output language during
DTV mode if there are multi languages available, during
ATV mode, press this button to select audio output like
mono & stereo.
4. MENU: Press this button to access the menu interface.
5. SLEEP: Use to auto power off by setting sleep timer.
6. NAVIGATION buttons: Press to select the options under
OSD setting interface or alter the settings in a menu.
7. (0~9 ): Enter numeric values and to select the channel or
program directly by entering its number.
TV OPERATION
GET STARTED
—
Be sure the TV antenna is connected to the set properly.
Plug the AC adaptor to the power source to power on
the TV set.
—
—
—
Slide power on/off switch to on position.
Press the TV/AV button on the remote or MODE button
on the main unit to select TV Mode.
—
Press AUTO/OK on the unit. Then select YES & press
AUTO button to program the channels onto the memory.
PROGRAMING BY REMOTE:
8. : Press to go to previously selected channel.
9. VOL-: Press this button to decrease the speaker volume.
10.POWER: Press this button to set the player to standby
on or off state( If the main power of the set is on).
11. ZOOM: Used to select the desired display mode wide or
normal. .
12. EXIT: Exit the menu interface.
13. EPG: Press this button to skim over TV programs guide.
14. OK/ENTER: Confirm the selection.
15. TV/AV: Select the desired signal input mode.
16. INFO: Press this button to display current program
information.
17. CH+: Press this button to increase the channel number.
18. CH-: Press this button to decrease the channel number.
19. - : Used to directly input TV channels.
Press the MENU button on the remote, and then select the
satellite image by using the key. Then press down arrow
button ( ) to select antenna function. Change to Air or
Cable by using button, depending upon the type of
connection. Then scroll to Auto Scan and press button
twice, TV will start auto programing function taking all the
available channels into memory.
NOTE: Auto Scan function has to be done for TV to capture
channels initially.
PROGRAMING FROM UNIT
Turn the TV on and press menu button, scroll to satelite
image by pressing Vol + ( ), and then press channel - (
to select antenna function. Press Vol + to choose Air or
cable reception. Then press CH - ( ) to select Auto scan
function and press Vol + ( ) and choose start scan by
using CH - ( ) and press Vol + ( ). The unit will start
program.
)
20. VOLUME +: Press this button to increase the speaker
volume.
SEARCH A PROGRAM
—
Press CH UP/DOWN button once, the channel number
changes. A desired channel can be reached using these
two keys.
—
NUMERIC button on the remote can facilitate you to
select a specific channel. If the channel number exceeds
10, input first digital unit, then another digital unit;
3
—
—
Note: this ATSC&Analog TV receiver can store the
channels from 2~69, and the maximum of each channel
has 8 programs. To select the desired programs by using
- button and numeric buttons.
Do as follows:
To select CH 13 NO. 2
OSD Duration
Sleep Timer
Time Zone
60 Sec
Off
Central
Off
Daylight Saving Time
Clock
----/--/-- --/--
Press 1 and 3, then press - and input 2.
Once the input is done, it will start broadcasting the selected
channel immediately.
UP/DOWN
ADJUST MENU:EXIT
OSD Duration: it is used to set the OSD display duration.
Sleep Timer: it is used to set the sleep timer to auto power
off the set.
Time Zone: it is used to select time zone from different
region.
ADJUST THE VOLUME
Too loud the voice will damage your ears, to adjust the
volume, use the VOLUME UP/DOWN buttons on the main
unit or on the remote control.
Daylight Saving time: it is used to advance one hour of the
daylight time in summer in order to save the power.
Clock: during DTV mode, it is used to show code create
date.
AUDIO EFFECT OPTIONS
This TV set is with two speakers inside the front panel,
which are enabled immediately it is powered on.
TV SETTING MENU
Menu Language
Color Mode
English
Press TV/AV button on the remote or MODE button on the
main unit to select TV mode, then Press once the MENU
button, the screen will pop up a setting menu;
Normal
Wide
Zoom Mode
Closed Caption
Restore Setting
use the NAVIGATION LEFT/RIGHT buttons to select among
the setting options, then press NAVIGATION UP/DOWN
button to enter the sub menu, again use NAVIGATION
LEFT/RIGHT button to select the desired option or adjust
and press OK/ENTER Button to confirm the item to be set;
Press MENU button to go to previously menu and press
EXIT button to exit the menu interface.
UP/DOWN
ADJUST MENU:EXIT
Menu Language: it is used to change menu language.
Color mode: it is used to change the color mode of screen.
Zoom Mode: it is used to select the display type.
Closed Caption: it is used to select the broadcasting
program provides closed caption. There are three options as
below:
CC mode: use to select on, CC on Mute, off.
Basic Selection: select among from CC1, Cc2, CC3,
CC4,Text1, Text2, Text3 and Text4.
Picture Mode
Contrast
Brightness
Sharpness
Tint
Personal
62
53
50
0
60
Color
Advance Selection: service 1, Service 2, Service 3, Service
4, Service 5, Service 6,
UP/DOWN
ADJUST MENU:EXIT
Restore Setting: select this option to restore the factory
setting.
Picture mode: it is used to select the desired picture mode.
Contrast: it is used to adjust the contrast effect according to
your own favorite.
Brightness: it is used to adjust the brightness effect
according to your own favorite.
Sharpness: it is used to adjust the sharpness according to
your own favorite.
Tint: it is used to adjust the tint effect according to your own
favorite.
Color: it is used to adjust the color according to your own
favorite.
Antenna
Air
Auto Scan
Show/Hide
Favorite
Channel No.
Channel Label
UP/DOWN
ADJUST MENU:EXIT
Antenna: it is used to select the Antenna type CATV or air.
Auto Scan: use this function to auto scanning and stored
tuned channels. Select auto scan option, then press
NAVIGATION RIGHT button to access the submenu, select
the desired Cable system and then enter the auto scan
option to begin auto scan.
Balance
0
Audio Language
English
Show/Hide:it is used to show or hide the programs
according to your own favorite.
UP/DOWN
ADJUST MENU:EXIT
Favorite: it is used to select your favorite programs.
Channel NO.: Select the desired program from this option.
Channel Label: it is used to edit the name of the selected
program.
Balance: it is used to adjust the balance effect according to
your own favorite.
Audio language: it is used to select the desired audio output
language.
4
Connecting to the DVD/VCD AV terminals
To power outlet
To video input connector (yellow)
To audio input connectors (red, white)
Video/audio cable
AC power cord
Video
L
R
Symptom
Remedy / Possible of causes
No picture and sound
Check the power supply.
Check the power switch and make sure it is at the ON position.
Make sure the channel is properly selected.
External antenna is used for poor reception area.
No picture
No sound
Check whether the volume is switch to low level or muted?
Headphone is inserted?
Picture is too dark
Picture is unstable
Check the brightness and contrast settings.
Adjust the direction, length of the antenna.
Signal is too weak.
Double image
Antenna angle is not correct.
Signal rebound from adjacent building etc.
"Snowy" on the screen
No colour
Power interference.
Make sure the system setting are correct.
ATTENTION
Due to the inherent nature of the Portable Televisions, this unit may not receive some channels, or may not have a
clear reception. This may be currently due to the weak nature of the digital over the air signals, or the location of
the unit from the transmitting Antenna.
5
Warranty
This Haier brand product, when shipped in its original
container, will be free from defective workmanship and
materials, and agrees that it will, at its option, either
repair the defect or replace the defective product with a
new or re-manufactured equivalent at no change to the
purchaser, for parts or labor for the periods set forth
below:
Responsibility of Haier to the purchaser with respect to
the product, and shall
constitute full satisfaction of all claims, whether based
on contract, negligence, strict duality or otherwise. In no
event shall Haier be liable, or in any way responsible for
any damages or defects in the product which were
caused by repairs or attempted repairs performed by
anyone other than an authorized service center or
dealer; nor shall Haier be liable, or in any way
responsible for incidental or consequential economic or
property damage. Some states do not allow the
exclusion of incidental or consequential damages, so
that above exclusion may not apply to you.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS
WHICH VARY FROM STATE TO STATE.
This warranty does not apply to the appearance of the
product or the exterior of the product, which has been
damaged or defaced, altered or modified in design or
construction. It does not apply to the additional
excluded items set forth below:
The warranty commences on the date the item was
purchased and the original purchase receipt must be
presented to the authorized service center before
warranty repairs are rendered.
Warranty period for this product: 90 days for Labor, one
year for parts.
The limited warranty described herein is in addition to
whatever implied warranties may be granted to
purchasers by law. ALL IMPLIED WARRANTIES
INCLUDING THE WARRANTIES OF MERCHANT
ABILITY AND FITNESS FOR USE ARE LIMITED TO
THE PERIOD(s) FROM THE DATE OF PURCHASE
SET FORTH BELOW. Some states do not allow
limitations on how long an implied warranty lasts, so the
above limitation may not apply to you.
Additional items excluded from warranty coverage: non-
rechargeable batteries.
Where to obtain service: For the location of the nearest
Haier authorized service center or to obtain product
literature, accessories, supplies or customer assistance,
please call 1-877-337-3639.
What to do to obtain service: ship or carry in your
product to an authorized service dealer or center .Be
sure to have proof of purchase.
If you ship the product, be sure it ispackaged carefully.
Haier America
New York, NY 10018
Neither the sales personnel of the seller nor any other
person is authorized to make any warranties other than
those described herein, or to extend the duration of any
warranties beyond the time period described herein on
behalf of Haier.
The warranties described herein shall be the sole and
exclusive warranties granted by Haier and shall be the
sole and exclusive remedy available to the purchaser.
Correction of defects in the manner and for the period
of time described herein, shall constitute complete
fulfillment of all abilities and
6
Haier
HLT71
|