nals to the Hunter terminals. Ignore the color of the wires,
as they do not always match the standard.
auxilliary heat strips will be activated for use as emergency heat
strips. See operation chart.
System Operation and Thermostat Check
Use the chart to check all functions of your thermostat. It ex-
plains the operation of your thermostat with the switches in vari-
ous positions. After checking, your thermostat is now ready for
operation. Set system to desired operations. Set thermostat
temperature lever to the room temperature. It takes at least
one hour after the room temperature has reached the thermo-
stat setting for all sensors to stabilize.
NOTE: In heat pump applications, time delays are involved
before the compressor can be activated to prevent short cy-
cling. The delays are provided by a minimum time off timer in
the heat pump unit which prevents the compressor from start-
ing for up to 5 minutes from when the thermostat last turned the
compressor off, or from the time the system first received power.
For technical support, contact us at 888-830-1326.
Installation of
Hunter Heat Pump Thermostat
Model 40080
®
®
Attaching Thermostat to Wall
1. Pull about 4 inches of thermostat wire through the wall open-
ing and lead through the large opening near the center of
the thermostat.
2. Attach the thermostat directly to the wall with screws and
anchors provided or to a standard horizontal outlet box us-
ing the two elongated mounting holes.
3. Level the thermostat. Use a level placed on top of the ther-
mostat for best results. Minor adjustments can be made
using the elongated holes. Securely tighten mounting
screws.
Heating Anticipation
This thermostat is equipped with fixed anticipators for stage
one heat and cooling which do not require adjustment. Stage 2
(or AUXilliary) heat has an adjustable anticipator.
Additional adjustments, if necessary, may be made as follows:
Heat cycles too long - Set adjustable heater to a slightly lower
dial setting (1/2 division).
Specifications
Thermal Data
Temperature Range:
Differential:
50°F to 90°F (10°C to 32°C)
Stage 1 Heat - 1 1/4°F
Stage 2 Heat - 0.1 to 1.2 Amps
Cooling - .2 to 1.0 Amp
Heat cycles too short - Set adjustable heater to a slightly higher
dial setting (1/2 division).
Operation and System Check
The chart shows the different system functions with switches in
various positions. Some models may not have certain system
functions.
Electrical Data
Switch Rating:
24 volts A.C. (30 VAC max.)
Stage 1 Heat - .2 to 1.2 Amps
Stage 2 Heat - 0.1 to 1.2 Amps
Cooling - .2 to 1.0 Amps
Sealed Mercury Switches
Stage 1 Heat & Cool - SPDT
Stage 2 Heat - SPST
Stage 1 Heat - 24 volts A.C. fixed
Stage 2 Heat - 0.1 to 1.2 Amps adjustable
Cooling - 24 volts A.C. fixed
IMPORTANT: This thermostat was calibrated at true level.
Any inaccuracy in level will cause control point deviation.
Care must be taken to mount the thermostat in a true level
position.
SwitchAction:
SWITCH POSITIONS
Emer Heat
SYSTEM FUNCTION
SYSTEM
Off
FAN
Fan
Relay
Rev
Compr. Aux
Em e r
Aux
Valve Contact Heat
Heat
Light
COMPONENT OPERATION
Cool
Heat
Norm
Emer
Auto
On
Disposal Information
Anticipator Rating:
This product contains mercury in a sealed tube. DO NOT place
this control in the trash at the end of its useful life.
If this product is replacing a control that contains mercury, DO
NOT place the old product in the trash.
No Heating, No Cooling, No Fan, No Lights.
Cooling Mode - Compressor contactor and fan relay cycle from
thermostat.
Safety
O
B
B
B
B
This thermostat is a precision instrument, and should be handled
carefully. Rough handling or distorting components could cause
the control to malfunction.
CAUTION: To prevent electrical shock and/or equipment dam-
age, disconnect electric power to system, at main fuse or circuit
breaker box, until installation is complete.
WARNING: Do not use on circuits exceeding 30 volts. Higher
voltage will damage control - could cause shock or fire hazard.
Do not exceed the specification ratings.
Contact your local waste management authority for instructions
regarding recycling and the proper disposal of this product, or
of and for any old control containing mercury in a sealed tube.
Heat Mode - Stage 1 Only - Compressor contactor and fan relay cycle
from thermostat.
Heat Mode - Both Stages - Compressor contactor, fan relay, auxiliary
heat relays, and aux. light on.
Attaching Thermostat Wire
1. Strip wires 1/4 inch.
2. Raise levers on terminal block. (Accepts 16 awg. stranded,
18-24 awg. sold or stranded)
3. Place leads into hole in terminal block under appropriate
terminal designation on circuit board and tightly close lever
by pushing downward. (Refer to wiring diagrams for proper
system hook-up.)
Emergency Heat Mode - Stage 1 Only - Fan and emergency heat relay
energized. Compressor locked out at thermostat. Emer. light on.
Emer. Heat Mode - Both Stages - Fan, emergency heat, and auxiliary
heat relays energized. Compressor locked out at thermostat. Emer.
and aux. lights on.
Installation
1. Remove the thermostat cover by carefully pulling outward
until it snaps free.
4. Push excess wire into wall or outlet box and plug up the
hole to preven drafts from affecting thermostat operation.
Fan runs continuously regardless of systemsw itch position.
2. Carefully remove and discard any packing which protects
the thermometer and the mercury switches during shipment.
3. If a thermostat is being replaced and it is in a satisfactory
location and the wiring is in good condition, use the exist-
ing wiring. If in doubt, have an electrician or HVAC profes-
sional replace the wiring.
4. If replacing an existing thermostat, place enclosed wire la-
bels on each wire to match the terminals on the old thermo-
stat. Refer to the wiring chart to help match the old termi-
Show s Position of Sw itch and System Function in Operation
This System Function w ill operate if jumper from Eto W2 is connected. (Optional)
Reversing valve energized if connected to "O" terminal
Reversing valve energized if connected to "B" terminal
O
B
Wiring Diagram
Failure to read and follow all instructions carefully, before in-
stalling or operating this thermostat, could cause personal in-
jury and/or property damage.
NOTE: The “Y” terminal activates the compressor contactor for
first stage HEAT and first stage COOL.
Wiring Chart and Diagram
Use the chart below to match the wires on your current system or thermostat. Most heat pumps will have connections like one of these.
NOTE: Remove the factory installed jumper if your heat pump has separate wires for E and W2.
The changeover relay valve is activated in either the COOLING
or the HEATING mode on all models. By connecting the relay
to the “0” terminal, the relay is activated by moving the system
switch to COOL. By connecting the relay to the “B” terminal the
relay is activated by moving the system to HEAT. Check your
owners manual for the appropriate connection for your system.
Common wire “X” must be connected for proper operation.
GREEN LIGHT (AUXiliary HEAT) - This light indicates auxiliary
heaters are assisting the heat pump in normal system opera-
tion. The aux. light will cycle with second stage heat in either
“NORMal HEAT” or “EMERgency HEAT” switch positions.
RED LIGHT (EMERgency HEAT) - This light will glow when the
emergency heat switch has been moved to the “EMER HEAT”
position. DO NOT use this switch for normal heating opera-
tions. The switch will bring on electric or gas auxilliary heat and
at the same time prevent the heat pump from operating.
With a jumper installed between “E” and “W2” terminals the
Hunter Connection Labels
Carrier Coleman Comfortmaker Bryant, Payne Rheem-Ruud Weathertron
York
R
Lennox (1) Lennox (2)
Two Mounting Holes
R
Y
O
B
G
E
24 VAC
R
Y or Y1
O
R
Y
R
Y
O
R
Y
R
Y
R
Y
O
R
Y
V-VR
M
Compressor
Y
Thermostat Cable Opening
Reversing valve - Cool
Reversing valve - Heat
Fan
O
O
O
R
B
G
B
G
G
E
G
G
E
G
G
G
E
F
E
Y
X
Emergency Heat
E
jumper to W2
E
jumper to W2 jumper to W2
W2 Auxillary Heat
Common
W2
C
W2
X
W1
C
W2
W2
X
W-U
B
W
B
W1
C
X
C, C1, X1
Note: W2 & X
w ires no
connection
Note: X2 & T
w ires no
connection
Flip-up Lever Terminal Block
Adjustment Second Stage
Lever Heat Anticipation
Hunter Fan Company
2500 Frisco Avenue
Memphis, Tennessee 38114
© 2002 Hunter Fan Company
41591-01 11/14/2002
|